St. Joseph, IL

Cleaned furnace burners and flame sensor, replaced the 16x25x5 filter, and checked static pressure and airflow. Inspected plumbing shut-off valves, tested toilet dye, checked crawl space for water leaks, and verified water pressure at 60 psi.

Replaced air filter, verified gas and static pressure, and cleaned the flame sensor, igniter, and burners for furnace HVAC maintenance. Inspected fixtures regarding a water pressure issue and advised coordinating with the well company.

Performed HVAC maintenance and plumbing inspection. Measured furnace gas pressure and temp rise, and cleaned burners, igniter, and flame sensor. Verified water heater gas valve, dye-tested toilets, and inspected sinks for leaks.

Inspected sump pumps, water heater, and plumbing fixtures during routine maintenance. Completed furnace maintenance and performed a CO2 test on an overheated flue pipe to verify structural integrity and safe operation with no active leaks.

Diagnosed a continuously running toilet and performed a full tank rebuild. Replaced the failed flapper seal, fill valve, and supply line, then installed a new toilet seat. Leak-tested the system to ensure reliable toilet repair.

Cleaned furnace burners, inspected the heat exchanger, and verified gas pressure and airflow for HVAC maintenance. Conducted plumbing checks, including toilet dye tests, water pressure testing, and shut-off valve inspections.

Performed furnace heating maintenance and replaced a failing inducer capacitor reading 2.8 of 5 microfarads. Also adjusted the water heater temperature down to "Hot" for safety and to prevent scalding.

Cleared a main sewer backup caused by tree roots. Accessed via a backyard PVC cleanout, rodded 40 feet of the line using a 3/4” cable and 4” cutter, and performed a camera inspection to confirm proper drainage.

Replaced a Mansfield toilet featuring a broken flush tower with a new Toto Drake. Installed a PVC spacer flange to correct a recessed flange below floor level, ensuring a proper seal and leak-free toilet repair.

Inspected mini-split systems during AC service and found they were not cooling due to low refrigerant. Scheduled an electronic leak search to locate the refrigerant leak and perform the necessary air conditioner repair.

Replaced deteriorating capacitor, 16x25x5 filter, and cleaned condenser coils during HVAC maintenance. Checked plumbing drains and provided quotes for a loose hallway toilet repair and a tankless water heater replacement.

Diagnosed a faulty float switch on the non-working sump pump. Replaced the unit with a new 237 sump pump, restoring proper basin drainage to prevent basement flooding.

Replaced water heater by adapting PEX to copper pipes, installing a new ball valve, flue fittings, and full port. Confirmed leak-free operation with passed gas and carbon monoxide safety tests. Advised client on future flue replacement.

Resolved outdoor unit buzzing with an AC repair, replacing a failed 2-pole contactor. Installed a compressor start kit to reduce startup time and strain, restoring quiet and efficient cooling performance.

Inspected non-operational 40-gallon gas water heater. Cleaned burner plate and pilot assembly, but the 20-year-old unit could not be restored. Provided estimate for water heater replacement, including required PEX piping adjustments.

Replaced washer boiler drain shut-offs. During the pipe repair, resolved a cracked CPVC fitting on the hot line by repiping with copper to a new drop ear. Installed and secured new valves, verifying leak-free operation.

Performed sewer camera inspection on the 4” PVC/clay line; verified no root infiltration or damage. Conducted water leak detection on the main-to-PEX line in the crawlspace, confirming no active leaks or pipe repairs are needed.

Upgraded bathroom plumbing by replacing the shower valve and trim kit. Installed two new shut-off ball valves and added an access panel for easier future maintenance. Tested the system thoroughly to ensure leak-free operation.

Replaced a degraded 40/5 uF capacitor during an air conditioner repair. Tested the system to ensure proper electrical readings, reliable startup, and efficient cooling.

Diagnosed Manitowoc ice machine not making ice. Found condensing fan motor not running due to a stuck-open fan cycling switch. Bypassed the switch to restore operation and recommended installing an aftermarket fan cycling switch.

Completed commercial furnace maintenance. Cleaned and inspected heating components for optimal performance and replaced the 20x25x1 air filter in the mezzanine. System is heating efficiently with all parts in good working order.

Replaced HVAC filter, cleaned condenser coils, and treated condensate line to ensure cooling. Inspected plumbing for leaks, verified water pressure, and recommended water heater replacement due to age.

Ran camera inspection on 4” sump pump line. Identified root infiltration and rocks from a broken 90-degree fitting. Marked blockage spot at 75 feet in the yard and advised customer on drain cleaning and repair options to restore flow.

Jetted storm drain catch basins and cleanouts using a Warthog nozzle. Removed significant root blockages and sediment buildup to restore proper water flow and complete necessary drain cleaning.

Replaced a leaking PVC drain pipe in the crawl space and secured hanging copper water lines with talon hangers to resolve water hammer. Also replaced a failed garbage disposal and basket strainer to restore proper kitchen drainage.