Fast, Reliable HVAC and Plumbing Services in Fisher, IL
Tucked along the Sangamon River in northern Champaign County, Fisher is a tight-knit farming village where neighbors still gather every year for the Fisher Community Fair and where many homes have stood for generations. Those older houses, long central-Illinois winters, and hardworking well and sewer systems all need a service company that shows up and gets it right. Lanz, Inc. has been that company since 2002, offering complete HVAC, plumbing, and underground solutions with a 4.9-star rating built on thousands of local reviews. Call 217-394-1380 or request service online to get on the schedule.
Fisher's Go-To Team for Furnace and Heating Repair
When the temperature drops below zero, a furnace that will not light is an emergency. It is also the call we answer most often in Fisher, where older homes and aging equipment mean worn flame sensors, failed inducer motors, and tired blower motors are common. Our technicians arrive stocked to diagnose and fix most no-heat problems in a single visit, and because many local homes still vent through masonry chimneys, we check flue and liner condition before we ever recommend a new appliance. Heating services in Fisher include:
- Furnace repair for no-heat calls, flame sensor cleaning, and inducer or blower motor replacement
- Furnace installation with proper flue and chimney evaluation on older homes
- Furnace maintenance to catch small issues before the coldest nights
- Boiler service for homes on hot-water heat
- Heat pump repair and installation for year-round efficiency
Cooling and Air Quality
Central-Illinois summers bring heat and humidity, and we keep Fisher homes cool and breathing easy on every make and model:
- AC repair for weak cooling, refrigerant issues, and failed contactors or capacitors
- AC installation sized correctly for your home
- Air conditioning maintenance to protect efficiency and extend system life
- Ductless mini-split systems for additions, upstairs rooms, and homes without ductwork
- Geothermal systems for long-term energy savings
- Duct cleaning, indoor air quality upgrades, and home automation and zoning
Plumbing Services
From a dripping faucet to a whole-house repipe, our licensed plumbers handle it all for Fisher homes and businesses:
- Plumbing repair for leaks, fixtures, toilets, and worn supply lines
- Plumbing installation and remodel work for kitchens and baths
- Repiping to replace aging galvanized or cast-iron pipe
- Water heaters and tankless water heaters, including chimney and flue checks on older installs
- Water treatment and water softeners for cleaner, gentler water
- Sump pumps to keep basements dry through spring storms
- RPZ and backflow services to protect your water supply
Drain and Sewer Cleaning
Recurring clogs and slow drains often point to something deeper in the line. Our NASSCO-certified team members find the cause and clear it:
- Sewer and drain cleaning for kitchen, bath, and main-line backups
- Main, sanitary, and storm drain cleaning for the toughest blockages
- Household drain cleaning for everyday slow drains
- Camera inspection to pinpoint scale, breaks, and obstructions before digging
Underground Solutions
For problems below the surface, we bring equipment most contractors cannot, which matters for rural properties on private septic and older service lines:
- Septic and leach field system installation and replacement
- New sewer pipes and water lines
- Interior pipelining and exterior pipelining to restore pipes without a full dig
- Pipe descaling for scaled cast-iron lines
- Directional boring, storm and drainage pipe work, and vactor services
Why Fisher Homeowners Call Lanz, Inc.
Family-owned since 2002, Lanz, Inc. serves all makes and models with transparent flat-rate pricing and a 100% satisfaction guarantee, backed by a team of highly trained technicians. Whether it is a furnace on the coldest night of the year or a slow drain that will not quit, help is available 24/7. Call 217-394-1380 or request service online.
Recent Jobs and Reviews in Fisher, IL
Job Locations and Reviews
Conducted water leak detection in basement. Found no plumbing leaks; water intrusion is coming from foundation cracks, causing wall staining. Sump pump is operational, but recommended a pump upgrade and basement waterproofing.
Inspected ductwork to address poor airflow in one room. Verified connections were intact and the single vent had sufficient airflow. Recommended installing an additional duct run and vent to improve air distribution, which was declined.
Inspected plumbing fixtures for leaks, tested sump pump, and flushed the water heater. For HVAC maintenance, checked the evaporator coil, measured furnace static pressure, tested refrigerant levels, and cleaned the exterior AC condenser coils.
Installed a new dehumidifier to improve indoor air quality. Ducted the system into the return, ran the condensate drain, wired low-voltage controls, set up the controller, and installed a wet switch safety puck. Tested for optimal operation.
Quoted a new 40-gallon short gas water heater. Noted that the chimney must be lined by a third-party company prior to installation, and furnace cement may be required for the flue entrance.
Installed a new top and corner panel on the outdoor air conditioner unit. Cycled power and restarted the system to ensure normal and efficient operation.
Investigated recurring toilet clog causing backup after multiple flushes. Performed drain cleaning to clear obstruction and restore full function.
Performed furnace repair: Replaced failed circuit board that caused 24V loss to gas valve, restoring proper heating system operation.
Investigated A/C not cooling and active water leak after prolonged operation. Further diagnostics needed to identify root cause and repair.
Addressed homeowner report of main sump pump operating intermittently.
Attempted drain camera from upstream manhole to locate new building tap. Unsuccessful.
Diagnosed furnace issue; confirmed stable operation after customer-performed power cycle. No additional HVAC repair needed.
Cleaned furnace burner assembly to restore proper flame signal from 0.7 uf, resolving no heat issue. Unit now operating normally.
Furnace not heating; replaced faulty inducer motor to restore proper furnace operation.
Replaced inducer motor in furnace. Verified proper furnace operation and inspected first-floor vents.
Furnace repair: Blower motor seized, causing no heat. Replaced motor to restore heating.
Reset toilet after leak was found. Old wax ring replaced. Toilet re-installed & sealed properly. "Plumbing repair" resolved.
Rebuilt kitchen sink drain and repaired waterline.
Sewer line inspection using camera revealed blockage. Accessed through PVC clean out in front yard to view bathroom, kitchen, and main sewer lines.
Kitchen sink leak traced to deteriorated drain pipes. Resolved with pipe replacement.
Inducer motor ordered; part arriving tomorrow. Repair will be scheduled once received. Replaced inducer motor.
Furnace repair: Flame sensor issue; unit failed to send signal to the control board after repeated attempts to ignite.
Inducer motor ordered for HVAC repair; awaiting part arrival tomorrow to schedule service.
HVAC - Furnace Problem, System was locked out when I arrived. I cycled power and tried running it. Everything turned on and the furnace lit correctly. However, before the blower motor could engage, I noticed the flame would go out. I checked the flame sensor with my meter and found it to be faulty. I installed a new flame sensor and now the furnace is running and working as designed. Replaced faulty flame sensor. Furnace now operating correctly after flameout issue prevented blower engagement.
HVAC - Furnace Problem, System was locked out when I arrived. I cycled power and tried running it. Everything turned on and the furnace lit correctly. However, before the blower motor turned on, the flame went out. I checked the flame sensor with my meter and found that the micro amps were low. Cleaned the flame sensor with steel wool and the furnace is now running properly. Cleaned furnace flame sensor. Low microamps were causing flameout before blower activation. Furnace now running correctly.